実車のスポークを張り替えるのにも混乱した私にとって  「凄い 」 としか言いようがないです☺

What a way to start this new build!

とても興味深い作業を見せて頂きました。同じ改造をしたい時には必見の動画ですね！

Nice work Kenji, those wheels are true👍🏾🐙

ワイヤースポークの張り替えは制作課題の一つなんです。いずれは、この動画を参考に作ってみたいです。

Superb work. I enjoy your work immensely

I don't speak Japanese, I don't do modeling, but I stayed to see the process. Thanks.

I’m currently lacing up some bicycle wheels, so I enjoyed this one more than usual. 👍

Bravo ! Superbe technique !

Very interesting to follow your work 👍

Hi Kenji san,  I am just as amazed as the first time I watched you do this.  The accuracy, and consistency is awesome. I look forward to all of your customizations on this. Thank you for sharing, and take care.:_kpmHeart:

自分も昆虫針を使ってスポーク張替えしていましたが、手に刺さりまくりで絶賛放置中です💦
動画を見て、再開するモチベーション頂きました。ありがとうございました。続きの製作動画を楽しみにしています。

Wonderful!  Than you!

これっすよこれ。期待通りのカスタム内容で嬉しいったらもう。じっくり見ま～す
[見たので追記]・・・はぁぁぁ（恍惚）素晴らしい内容でした。リム側は想像通りでしたがハブ側どうすんのかなと思ってたらラジペンでくいっと曲げて一丁上がりとは全くもって恐れ入ります。ある意味実物よりも大変そうなスポーク組みでした（実物はスポークは自作しない）センターもそこそこ出てて全く素晴らしいとしか言いようが、いやもう感動しましたよマジで。私らは動画で見られて幸せですが、実作業は1組8時間ぐらいでしょうか？（見当違いならごめんなさい）根気と集中力が異次元です。BGMも素敵すぎです。本物に本物が引き寄せられたって事でしょうか。次回も楽しみです！

Thank you, Kenji. I remove plating in two stages. The first is to soak the parts in caustic soda (or use a strong oven cleaner such as Oven Pride). Wash the larts in water once the plating has dissolved away (can take some hours). Then remove the lacquer layer underneath using Dettol bleach. Vive final wash when done.

황금손을 갇고 계신 모델러분 대단하시다는 말밖에 없내요 부러울 따름 입니다 항상 응원 합니다 ❤

治具の作り方、インセクトピンを使うなど、もう技術解説書

Some tips:

Ribbed cylinders (sheaves etc) can be prepared with fine needle files of appropriate profile (triangle for 60⁰, square for 90⁰, half square for 45⁰, blade for 15⁰ etc) roughly, then refined with sharp blade.

Perfect chopping of small tubes and wires is easy with rotating tool and diamond disc. Rotate wire/tube slowly with fingers and touch the end with diamond disc - this will make it perfect clean. Then touch the wire/tube at needed length with disc at 45⁰ angle - this will make a grove so you can snap it off and press insert where it belongs to. Then clean the end and repeat.

Chrome plated sprues made by 1) priming the plastic with self levelling coat; 2) plating over with chrome in vacuum; 3) overcoating for durability. So you have to dissolve all layers. Try various chemicals, not very agressive to PS plastic.

Spokes... probably it would be better to insert heads into 0.3 mm holes in hubs, then supergluing aligned spokes between rim halves. I've seen people prepare groves in rims from inside for tubes with spokes, instead of drilling into glued rim.

Good luck!

Thanks for this great video. I want to try it for the first time on my 1:6 Honda CRF 1000L.

Wow that's a lot of work Kenji-san, but the result is magnificent so it was worthy 😊 I see that insect pin are really useful for a lot of things, I hope I can get them in Europe. Waiting for the next video!