Can’t believe I never noticed the two colours on the right hand side measurement.
Will be doing some adjustments next week.
Thank you

Really helpful video.  I've had my 5-S for almost a year now and it's been great. It's definitely a recommended purchase from me.  I've relied on other channels to get the fine-tune information before now, so it's great Evolution have produced this officially.  
I do however have some small issues with the 5-S;
1.  You have to have the blade too high to allow the material to pass easily under the guard in my opinion - though maybe my riving knife is too low.
2. The mitre gauge is too loose in the slot so isn't as accurate as it should be.  Think the end caps on this gauge should be removed and just have a larger metal section.
3. It's annoying that the cart handles are above the wheels - they should be opposite them so it can be more easily manoeuvred into position.

Just got one for a present. Watching the vids after reading manual to make sure i do it right. This saw if it works like ive seen will get lots of use.

Thank you for the Informative video. I’ve had my Rage5S for a year or so now and now I know how to fine tune it.
I bought this saw for a few reasons:
1. Fence is full length and by far the smoothest of the models I looked at. Well ahead of some of the big brands.
2. Portability and being able to store it in my small garage.
3. Sliding panel on the table when using the mitre gauge.
4. Table Extension wings allowing the table surface to be widened to 1.2m
Challenges:
1. The left and right mitre slots are different widths! Right slot is narrower than the left.
2. With the left slot being wider that accounts for the slop when using the mitre gauge even when screwed down on the sliding panel. A few pieces of painters tape fixed that.
3. Sliding panel racks from side to side. Had to adjust its rails to fix that.
4. Blade guard is poorly designed and in my view more dangerous than a safety feature. Also the dust port connector is mostly blocked by poorly located screws which hold the two halves of guard together. I’ve removed mine.
5. Riving knife needs to be tightened correctly to avoid it misaligning it with the blade
Overall I love this saw. Features for the price can’t be beat. You just need to take the time to setup and tune the saw first. Something I did not realise as this was my first table saw.

One of the best things I’ve bought and a great addition to my shop. Can move it about and take it on site. Does it all. Thanks for making this video

Great instruction. Just bought a Rage 5s and this is easy to follow.

Thanks Lee, that was a very helpful videoon the whole.
There is one thing though. If you want to allign the blade so its parallel with the fence you need to undo both the bolts at the back as they are in the same metal bar. If you undo just the one then there is no adjustability. My advice is to undo both those bolts just a little so you can tap the metal bar with a hammer until the blade is parallel and then tighten them again.

Otherwise great video and thanks  🙏

I learnt alot from this. Thanks!

Thanks Lee. Really useful.

Very helpful vid, thankyou!

Great instructions thank you.

Great, cannot wait for the next one on cutting

Super video.

Great video; there has been a lot of criticism regarding the accuracy of Evolution saws; I think this is mainly because of the lack of seting up knowledge; as you say your saws are factory set; however people forget that transportation can affect this and they should check accuracy before starting; I have the Rage 3 DB which is great except for the handle which I dislike intensely I much prefer the newer horizontal style handles (no I am not selling and buying the newer model 😂 but if the new handles fitted my saw I would definitely consider replacing it); I will say that the multi blade is a good aground saw; I have used one on both Unistrut and wood even on Dexion (the saw didn’t like the angle of the Dexion but with patience and safety in mind it worked); I have noticed that Evolution now make a 60T wood cutting blade that fits both this and the table saw; as soon as budget allows (I am an engineer and currently out of work but hey ho) I will be buying both the 60T wood blade and the Rage 5 S as the blade will complement both saws 😊 I was considering a more expensive saw but your video may just have converted me 😉

Not sure if older versions vary (mine was made in 2018), but I found that I had to loosen both hex bolts behind the riving knife in order to adjust the blade angle. Boy, were they tight! Got it and the fence sorted now.

Très belle machine :) elle doit être bien pratique .

My Rage 5S table extender locking lever has become loose and isn't locking the sliding extension tightly. How can this lever be adjusted to tighten it and create a solid locking of the table extender? My table saw isn't over used by any means and was assembled less than 1 year ago

hi i have one how do you stop blade wobble

what about the absolute inexistant dust extraction ????

Could you do a video just like this for the fury5-s