Great info..I'm sure I'm I'm thebonly one who greatly appreciates ya taking time to post this much needed info...good job sir!

How do you  adjust the cut out pressure?

Do a review of a 2
Stage 30 gallon w Honda 13 horse.

That is the same compressor i have and it shuts down at 40 psi and no throttle control

I have a Rolair GX270 compressor Honda I ned a unloader valve & throttle control.

Can a 15hp gas engine works with a 10 hp pump for a air compressor?

good stuff. thank you

Can you give part number for pilot valve

Hello, and thankyou for the video. I have the same compressor for a roofing company of mine and although it has increasingly with time and wear become a bit more troublesum to get started it generally starts after 3 or 4 pulls however today during a job when the rain was on it's way and I needed it the most the damn thing kept stalling out on me! And by that I mean that it would start up, run for 15 sec - 2 min and then the motor would die. My guy that stays on the ground that cleans up during tare offs is for the most part also supposed to keep up with the maintenance on the compressors but since he's a fat lazy piece of sh** he hasn't done anything but eat and poop. (Gross I know) Enough about him, so here's what I know and have tried...I know I'm using the fuel and choke levers correctly, if it's hard to start then I'll make sure I open all valves and release all pressure, I'll loosen the fuel cap just in case of any vapor lock possibilities, there is engine oil (although it could probably need a good changing), there is compressor oil maybe even to much...the bubble is so faded and cloudy and full of "work" that its impossible to see through however after adding a little bit of oil today I noticed that a little bit was squirting out of the cap through the tiny relieve holes at the top so yeah, probably to much but that happened after it was giving me trouble anyway...I'm thinking maybe the throttle control may need to be adjusted but idk because when the unit shutoff and dies after running for a min it shuts off pretty abruptly like if you were to hit the off switch, it's not like starving for fuel or choking out...it just shuts off, kinda like something is telling it to shutoff. Is there some kind of safety something that shuts off the motor if something isn't right with the compressor? I'm pretty knowledgeable when it come to small engines so I'm not just writing this book on YouTube without after troubleshooting this thing with a fair amount of mechanical knowhow first. Any help would be much appreciated!! Thanks in advance!!

Anyone Here Has A Diagram On How To Make An Air Compressor Gas Powered Using The Pilot Valve ?

Why don’t they put a centrifugal clutch on the engine so when the engine idles down it shuts the pump off.  I went out and let my compressor cool down fired up the engine and let it idle and was amazed how much heat the compressor pump was making.  Very little air flow sadly with these gas compressors.   Rol air does seem to have a better flywheel than others

Mine is converted from a 3hp electric motor to a 212cc petrol engine.
It has throttle control but i didn't use a pilot unloader valve. I used a component that cost less than a fiver.

What is the one black adjustment vavle on the pump it self

My  has Kohler 14 hp went out on my Ingersoll rand compressor.  Can I install a 22 hp preditor engine from harbor fright also can a bullwhip be installed on that engine????

One more question I have one just about like this but low and behold the model and serial number is wore were I can't see it my question is this is parts for the pump pretty much all same from diagrams that I have look at they look the same

Hi, if I am understanding this correctly,  gas compressors don't have a centrifugal clutch, is that correct? Is the engine turning the pump when you are trying to start it? Does unloading the pilot valve make it possible to start the engine?

Who sales replacement air com tanks?

how do you adjust the governor on this unit? can someone help me, I was adjusting that little screw and now it won't run correctly so I want to reset it to factory but can't find it in the manuals anywhere

How about a gas powered pressure washer? Anything about that different than a compressor?

this is great while also being relatively worthless at the same time. It would have been brilliant to start at the beginning of the system and work your way through the system in the flow that the air is created and moved and then delivered. Like this is the engine which drives the pulley on the pump and air comes out of the pump here goes through this valve and into the tank here comes out of the tank here through this valve and does this that way someone understood the flow of the air being made and what controls it.